D8T Track-Type Tractor
360° Exterior View
360° Interior View
At a Glance
|
|
|
|
Overview
Engine
+ -Engine Model | Cat C15 ACERT™ |
Flywheel Power | 354HP |
Emissions | U.S. EPA Tier 4 Final/EU Stage IV/Korea Tier 4 |
Net Power - 1,900 rpm - ISO 9249/SAE J1349 | 354HP |
Engine Power - 1,600 rpm - ISO 14396 | 394HP |
Displacement | 928in³ |
Note (3) | All nonroad Tier 4 Final, Stage IV and Korea Tier 4 Final diesel engines are required to use only Ultra Low Sulfur Diesel (ULSD) with 15 ppm (mg/kg) of sulfur or less, or up to B20 biodiesel blended with ULSD. B20 should meet ASTM D7467 specification (bio |
Note (4) | Diesel Exhaust Fluid (DEF) used in Cat Selective Catalytic Reduction (SCR) systems must meet the requirements outlined in the International Organization for Standardization (ISO) standard 22241. |
Bore | 5.4in |
Stroke | 6.75in |
Engine Power - 1,700 rpm - SAE J1995 | 363HP |
Engine Power - 1,700 rpm - ISO 14396 | 359HP |
Engine Power - 1,700 rpm - ISO 14396 (DIN) | 364HP |
Net Power - 1,900 rpm - ISO 9249/SAE J1349 (DIN) | 317HP |
Engine Power - Maximum - ISO 14396 | 359HP |
Engine Power - Maximum - ISO 14396 (DIN) | 364HP |
Engine Power - Maximum - SAE J1995 | 363HP |
Net Power - Rated - ISO 9249/SAE J1349 | 312HP |
Net Power - Rated - ISO 9249/SAE J1349 (DIN) | 317HP |
Note (1) | Net power advertised is the power available at the flywheel when the engine is equipped with fan, air cleaner, muffler, and alternator. |
Note (2) | No derating required up to 3566 m (11,700 ft) altitude, beyond 3566 m (11,700 ft) automatic derating occurs. |
Weights
+ -Operating Weight | 86900lb |
Operating Weight - Standard | 87600lb |
Shipping Weight - Standard SU Blade | 66300lb |
Operating Weight - LGP | 82496lb |
Shipping Weight - LGP | 68700lb |
Note (1) | Operating Weight – Standard: Includes hydraulic controls, blade, tilt cylinder, coolant, lubricants, 100% fuel, ROPS, FOPS cab, SU-Blade, Single-Shank Ripper, 610 mm (24 in) MS shoes, and operator. |
Note (2) | Operating Weight – LGP: Includes hydraulic controls, blade, tilt cylinder, drawbar, coolant, lubricants, 100% fuel, ROPS, FOPS cab, SU-Blade, 965 mm (38 in) MS shoes, and operator. |
Note (3) | Shipping Weight – Standard: Includes coolant, lubricants, 20% fuel, ROPS, FOPS cab, and 610 mm (24 in) MS shoes. |
Note (4) | Shipping Weight – LGP: Includes coolant, lubricants, 20% fuel, ROPS, FOPS cab, and 965 mm (38 in) MS shoes. |
Air Conditioning System
+ -Air Conditioning | The air conditioning system on this machine contains the fluorinated greenhouse gas refrigerant R134a (Global Warming Potential = 1430). The system contains 2.5 kg of refrigerant which has a CO2 equivalent of 3.575 metric tonnes. |
Blades
+ -8SU - Capacity - SAE J1265 | 13.4yd³ |
8SU - Width - Over End Bits | 13.3ft |
8U - Capacity - SAE J1265 | 15.4yd³ |
8U - Width - Over End Bits | 14ft |
8A - Capacity - SAE J1265 | 6.8yd³ |
8A - Width - Over End Bits | 16.5ft |
8SU LGP - Capacity - SAE J1265 | 12.9yd³ |
8SU LGP - Width - Over End Bits | 14.9ft |
Transmission
+ -1 Forward | 2.1mile/h |
2 Forward | 3.8mile/h |
3 Forward | 6.6mile/h |
1 Reverse | 2.8mile/h |
2 Reverse | 5mile/h |
3 Reverse | 8.8mile/h |
1.0 Forward | 2.2mile/h |
2.0 Forward | 4.1mile/h |
3.0 Forward | 7mile/h |
2.0 Reverse | 4mile/h |
3.0 Reverse | 7.3mile/h |
1 Forward - Drawbar Pull | 148200lb |
2 Forward - Drawbar Pull | 82300lb |
3 Forward - Drawbar Pull | 46250lb |
Drawbar Pull - 1 Forward | 148lb |
Drawbar Pull - 2 Forward | 81lb |
Drawbar Pull - 3 Forward | 44lb |
Service Refill Capacities
+ -Fuel Tank | 165gal (US) |
DEF Tank | 6.3gal (US) |
Cooling System | 22.7gal (US) |
Engine Crankcase* | 10gal (US) |
Power Train | 41gal (US) |
Roller Frames - Each | 17.2gal (US) |
Final Drive - Each | 3.3gal (US) |
Pivot Shaft Compartment | 10.6gal (US) |
Hydraulic Tank | 19.8gal (US) |
Note | *With oil filter |
Operating Weights
+ -Standard | 87600lb |
LGP | 83200lb |
Hydraulic Controls
+ -Pump Type | Piston-type, Variable Displacement |
Pump Output - Steering | 75gal/min |
Pump Output - Implement | 64gal/min |
Tilt Cylinder Flow - Rod End Flow | 35gal/min |
Tilt Cylinder Flow - Head End Flow | 45gal/min |
Bulldozer Relief Valve Setting | 3480psi |
Tilt Cylinder Relief Valve Setting | 3480psi |
Ripper - Lift - Relief Valve Setting | 3480psi |
Ripper - Pitch - Relief Valve Setting | 3480psi |
Steering | 5700psi |
Note (1) | Steering Pump output measured at 2,364 rpm (pump speed) and 30 000 kPa (4,351 psi). |
Note (2) | Implement Pump output measured at 1,900 rpm and 6895 kPa (1,000 psi). |
Note (3) | Electro-hydraulic pilot valve assists operations of ripper and dozer controls. A standard hydraulic system includes four valves. |
Note (4) | Complete system consists of pump, tank, filter, oil cooler, valves, lines, and control levers. |
Weights - Waste Handler
+ -Operating Weight - Standard | 87400lb |
Operating Weight - LGP | 92300lb |
Shipping Weight - Standard | 73400lb |
Shipping Weight - LGP | 77900lb |
Note (1) | Operating Weight – Standard: Includes hydraulic controls, blade, tilt cylinder, coolant, lubricants, 100% fuel, ROPS, FOPS cab, Waste SU-Blade, striker box, 610 mm (24 in) MS shoes, and operator. |
Note (2) | Operating Weight – LGP: Includes hydraulic controls, blade, tilt cylinder, drawbar, coolant, lubricants, 100% fuel, ROPS, FOPS cab, Waste SU-Blade, 965 mm (38 in) MS shoes, striker box, and operator. |
Note (3) | Shipping Weight – Standard: Includes coolant, lubricants, 20% fuel, ROPS, FOPS cab, striker box, and 610 mm (24 in) MS shoes. |
Note (4) | Shipping Weight – LGP: Includes coolant, lubricants, 20% fuel, ROPS, FOPS cab, striker box, and 965 mm (38 in) MS shoes. |
Winches
+ -Winch Model | PA 140OVS |
Weight* | 3947lb |
Oil Capacity | 4gal (US) |
Increased Tractor Length | 22.2in |
Winch Case - Width | 45.6in |
Drum Width | 12.6in |
Flange Diameter | 18in |
Cable Ferrule Size - Length | 2.76in |
Cable Ferrule Size - Outside Diameter | 2.36in |
Drum Capacity - Optional Cable | 193ft |
Drum Capacity - Recommended Cable Size | 276ft |
Optimal Cable Size | 1.25in |
Recommended Cable Size | 1.13in |
Winch Length | 56.3in |
Note (1) | *Weight: Includes pump and operator controls. |
Note (2) | Variable speed, hydraulically driven, dual braking system, three roller fairlead. |
Dimensions - Standard
+ -Width - Tractor - Without Trunnions - Standard Shoes | 106in |
Machine Height - ROPS/FOPS Cab | 140.4in |
Length - Track on Ground | 126.2in |
Overall Length - Basic Tractor | 183in |
Ground Pressure (ISO 16754) | 13psi |
Ground Clearance | 24.1in |
Undercarriage - LGP
+ -Ground Clearance | 24.1in |
Ground Contact Area | 9593in² |
Ground Pressure (ISO 16754) | 7.7psi |
Grouser Height | 3.1in |
Length - Track on Ground | 126in |
Pitch | 8.5in |
Shoe Type | Moderate Service |
Shoes/Side | 44 |
Track Gauge | 92in |
Track Rollers - Each Side | 8 |
Width - Shoe | 38in |
Undercarriage - Standard
+ -Ground Clearance | 24.1in |
Ground Contact Area | 6060in² |
Ground Pressure (ISO 16754) | 13psi |
Grouser Height | 3.1in |
Length - Track on Ground | 126in |
Pitch | 8.5in |
Shoe Type | Moderate Service |
Shoes/Side | 44 |
Track Gauge | 82in |
Track Rollers - Each Side | 8 |
Width - Shoe | 24in |
Blades - 8A
+ -Height | 3.9ft |
Digging Depth | 24.6in |
Ground Clearance | 52.1in |
Maximum Tilt | 28.9in |
Weight* - Without Hydraulic Controls | 11900lb |
Total Operating Weight** - With Blade and Single-Shank Ripper | 88700lb |
Note (1) | *Includes blade tilt cylinder. |
Note (2) | **Operating Weight: Includes hydraulic controls, blade tilt cylinder, coolant, lubricants, 100% fuel, ROPS, FOPS cab, blade, single-shank ripper, 610 mm (24 in) MS shoes, and operator. |
Capacity - SAE J1265 | 6.8yd³ |
Width - Over End Bits | 16.6ft |
Blades - 8SU LGP
+ -Capacity - SAE J1265 | 12.9yd³ |
Width - Over End Bits | 14.9ft |
Height | 5.3ft |
Digging Depth | 20.2in |
Ground Clearance | 51.5in |
Maximum Tilt | 35.7in |
Weight* - Without Hydraulic Controls | 11150lb |
Total Operating Weight** - With Blade and Single-Shank Ripper | 82496lb |
Note (1) | *Includes blade tilt cylinder. |
Note (2) | **Operating Weight: Includes hydraulic controls, blade tilt cylinder, coolant, lubricants, 100% fuel, ROPS, FOPS cab, blade, single-shank ripper, 610 mm (24 in) MS shoes, and operator. |
Blades - 8 SU Landfill
+ -Capacity - SAE J1265 | 25.6yd³ |
Width - Over End Bits | 12.9ft |
Height | 8.1ft |
Digging Depth | 22.6in |
Ground Clearance | 50.7in |
Maximum Tilt | 35.1in |
Weight* - Without Hydraulic Controls | 7867lb |
Total Operating Weight** - With Blade and Single-Shank Ripper | 88800lb |
Note (1) | *Includes blade tilt cylinder. |
Note (2) | **Operating Weight: Includes hydraulic controls, blade tilt cylinder, coolant, lubricants, 100% fuel, ROPS, FOPS cab, blade, single-shank ripper, 610 mm (24 in) MS shoes, and operator. |
Blades - 8U Landfill
+ -Capacity - SAE J1265 | 27.7yd³ |
Width - Over End Bits | 13.9ft |
Height | 8.3ft |
Digging Depth | 22.3in |
Ground Clearance | 48.8in |
Maximum Tilt | 39.2in |
Weight* - Without Hydraulic Controls | 9450lb |
Total Operating Weight** - With Blade and Single-Shank Ripper | 90383lb |
Note (1) | *Includes blade tilt cylinder. |
Note (2) | **Operating Weight: Includes hydraulic controls, blade tilt cylinder, coolant, lubricants, 100% fuel, ROPS, FOPS cab, blade, single-shank ripper, 610 mm (24 in) MS shoes, and operator. |
Blades - 8 SU LGP Landfill
+ -Capacity - SAE J1265 | 28.9yd³ |
Width - Over End Bits | 14.9ft |
Height | 7.9ft |
Digging Depth | 20.2in |
Ground Clearance | 51.5in |
Maximum Tilt | 35.7in |
Weight* - Without Hydraulic Controls | 7734lb |
Total Operating Weight** - With Blade and Single-Shank Ripper | 83635lb |
Note (1) | *Includes blade tilt cylinder. |
Note (2) | **Operating Weight: Includes hydraulic controls, blade tilt cylinder, coolant, lubricants, 100% fuel, ROPS, FOPS cab, blade, single-shank ripper, 610 mm (24 in) MS shoes, and operator. |
Ripper - Multi-Shank, Adjustable Parallelogram
+ -Total Operating Weight* - With SU-Blade and Ripper | 86876lb |
Note | *Total Operating Weight: Includes hydraulic controls, blade tilt cylinder, coolant, lubricants, 100% fuel. ROPS, FOPS cab, blade, single-shank ripper, 610 mm (24 in) MS shoes, and operator. |
Maximum Clearance Raised - Under Tip, Pinned in Bottom Hole | 23.35in |
Maximum Penetration - Standard Tip | 30.7in |
Maximum Penetration Force - Shank Vertical | 27920lb |
Number of Pockets | 3 |
Overall Beam Width | 97in |
Pry-Out Force - Multi-Shank Ripper with One Tooth | 51230lb |
Weight - Each Additional Shank | 732lb |
Weight - With One Shank | 8681lb |
Standards
+ -Note (4) | The declared dynamic operator sound pressure level is 75 dB(A) when “ISO 6396:2008” is used to measure the value for an enclosed cab. The measurement was conducted at 70% of the maximum engine cooling fan speed. The sound level may vary at different engin |
Note (5) | The declared exterior sound power level is 113 dB(A) when the value is measured according to the dynamic test procedures and the conditions that are specified in “ISO 6395:2008.” The measurement was conducted at 70% of the maximum engine cooling fan speed |
FOPS | Falling Object Protective Structure (FOPS) meets the following criteria: ISO 3449:2005 Level II. |
ROPS | Rollover Protective Structure (ROPS) meets the following criteria: ISO 3471:2008. |
Note (1) | The declared dynamic operator sound pressure level is 76 dB(A) when “ISO 6396:2008” is used to measure the value for an enclosed cab. The measurement was conducted at 70% of the maximum engine cooling fan speed. The sound level may vary at different engin |
Note (2) | Hearing protection may be needed when the machine is operated with an open operator station for extended periods or in a noisy environment. Hearing protection may be needed when the machine is operated with a cab that is not properly maintained or when th |
Note (3) | Sound Level Information for Machines in European Union Countries and in Countries that Adopt the “European Union Directives” – The information below applies to only the machine configurations that have the “CE” mark on the Product Identification Plate. |
Brakes | Crawler Machine Brake Requirements meets the following criteria: ISO 10265:2008. |
Blades - 8SU - Version 1
+ -Capacity - SAE J1265 | 11.3yd³ |
Digging Depth | 22.6ft |
Ground Clearance | 50.7in |
Height | 5.5in |
Maximum Tilt | 35.1lb |
Note (1) | *Includes blade tilt cylinder. |
Note (2) | **Operating Weight: Includes hydraulic controls, blade tilt cylinder, coolant, lubricants, 100% fuel, ROPS, FOPS cab, blade, single-shank ripper, 610 mm (24 in) MS shoes, and operator. |
Total Operating Weight** - With Blade and Single-Shank Ripper | 86900ft |
Weight* - Without Hydraulic Controls | 10100lb |
Width - Over End Bits | 12.9in |
Blades - 8SU - Version 2
+ -Capacity - SAE J1265 | 13.4yd³ |
Digging Depth | 22.8in |
Ground Clearance | 48.7in |
Height | 5.7ft |
Maximum Tilt | 36in |
Note (1) | *Includes blade tilt cylinder. |
Note (2) | **Operating Weight: Includes hydraulic controls, blade tilt cylinder, coolant, lubricants, 100% fuel, ROPS, FOPS cab, blade, single-shank ripper, 610 mm (24 in) MS shoes, and operator. |
Total Operating Weight** - With Blade and Single-Shank Ripper | 86900lb |
Weight* - Without Hydraulic Controls | 10557lb |
Width - Over End Bits | 13.3ft |
Blades - 8U
+ -Capacity - SAE J1265 | 15.4yd³ |
Digging Depth | 22.3in |
Ground Clearance | 48.8in |
Height | 5.7ft |
Maximum Tilt | 39.2in |
Note (1) | *Includes blade tilt cylinder. |
Note (2) | **Operating Weight: Includes hydraulic controls, blade tilt cylinder, coolant, lubricants, 100% fuel, ROPS, FOPS cab, blade, single-shank ripper, 610 mm (24 in) MS shoes, and operator. |
Total Operating Weight** - With Blade and Single-Shank Ripper | 88300lb |
Weight* - Without Hydraulic Controls | 11500lb |
Width - Over End Bits | 13.9ft |
Ripper - Single-Shank, Adjustable Parallelogram
+ -Maximum Clearance Raised - Under Tip, Pinned in Bottom Hole | 25in |
Maximum Penetration - Standard Tip | 44.4lb |
Maximum Penetration Force - Shank Vertical | 28620lb |
Note | *Total Operating Weight: Includes hydraulic controls, blade tilt cylinder, coolant, lubricants, 100% fuel. ROPS, FOPS cab, blade, single-shank ripper, 610 mm (24 in) MS shoes, and operator. |
Number of Pockets | 1 |
Pry-Out Force | 50070in |
Total Operating Weight* - With SU-Blade and Ripper | 86900lb |
Weight* - Without Hydraulic Controls | 8705lb |
Dimensions - Non-Suspended
+ -Width - Tractor - Without Trunnions - Standard Shoes | 106in |
Machine Height - ROPS/FOPS Cab | 140.7in |
Length - Track on Ground | 128.3in |
Overall Length - Basic Tractor | 183in |
Ground Pressure (ISO 16754) | 13psi |
Ground Clearance | 23.8in |
Dimensions - LGP
+ -Width - Tractor - Without Trunnions - Standard Shoes | 130in |
Machine Height - ROPS/FOPS Cab | 140.4in |
Length - Track on Ground | 126.2in |
Overall Length - Basic Tractor | 183in |
Ground Pressure (ISO 16754) | 7.7psi |
Ground Clearance | 2401in |
Dimensions
+ -Note (1) | Add the following measurements for attachments: Ripper (single shank) 1519 mm/59.8 in; Ripper (multi-shank) 1613 mm/63.5 in; Drawbar 406 mm/16.0 in; SU Blade 1844 mm/72.6 in; U Blade 2241 mm/88.2 in; A Blade (not angled) 2027 mm/79.8 in; A Blade (angled 2 |
Note (2) | When Cat Grade Control 3D antennas are installed, overall machine height increases by approximately 82 mm/3.2 in. |
Standard Equipment:
Power Train
+ --
C15 ACERT Diesel Engine: – Electronic Unit Injection (EUI) – Aftertreatment – Meets Tier 4 Final/Stage IV/Korea Tier 4 emission standards
-
24V electric start
-
High performance single plane cooling system
-
Aftercooler, air-to-air (ATAAC)
-
Air filter, with electronic service indicator
-
Coolant, extended life
-
Fan, suction, hydraulically driven
-
Fuel priming pump, electric
-
Sound attenuated exhaust system
-
Parking brake, electronic
-
Precleaner, strata-tube dust ejector
-
Prescreener
-
Shift management: – Automatic directional and downshift – Controlled-throttle, load-compensated – Enhanced Auto Shift
-
Starting aid, automatic ether
-
Torque divider
-
Transmission, electronically-controlled powershift, 3F/3R speed
-
Four planet, double-reduction planetary final drives
-
Transmission control module, electronic
-
Turbocharger
-
Water separator
Undercarriage
+ --
Rollers and idlers, lifetime lubricated
-
Sprocket rim segments, replaceable
-
Suspension-type undercarriage
-
8-roller tubular track roller frame (Carrier roller ready)
-
Track adjusters, hydraulic
-
Track guide
-
610 mm (24 in) PPR moderate service grouser with sealed and lubricated track (44 section)
-
Two-piece master links
Hydraulics
+ --
Hydraulics, independent steering and work tool pumps
-
Hydraulics, electronically controlled, load-sensing dozer lift and tilt
-
Electronically enabled quick drop valve
Starters, Batteries, And Alternators
+ --
Alternator, 150 amp
-
Batteries, heavy duty
-
Starting receptacle, auxiliary
Electrical
+ --
Alarm, back-up
-
Converter, 24V to 12V
-
Diagnostic connector
-
Ground level service center with hour meter
-
Horn, forward warning
Operator Environment
+ --
ROPS mounted air conditioner
-
Armrest, adjustable
-
Advisor operator interface: – Electronic monitoring system – Diagnostic service information – Operator preferences
-
Cab, ROPS/FOPS, sound suppressed
-
Deactivation switch, hydraulic controls
-
Access/egress lighting with shutdown timer
-
Decelerator pedal
-
Governor switch, electronic
-
Heater and ventilation
-
Mirror, rearview
-
Radio-ready
-
Provision for wire passage in/out of cab
-
Interior LED courtesy lights
-
Seat, cloth, air-suspension
-
Seat belt, retractable
-
Steering control, direction and speed control thumb switches with recall button
-
Wipers, intermittent
Other Standard Equipment
+ --
CD ROM Parts Book
-
Engine enclosures
-
Equalizer bar, pinned
-
Front pull device
-
Guards, bottom hinged
-
Grade control ready
-
HVAC box – corrosive resistant
-
Mounting, lift cylinders
-
Oil cooler, hydraulic
-
Product Link
-
S·O·S sampling ports
-
Steering, electronically controlled power differential
-
Vandalism protection for fluid compartments
-
Engine compartment service light
-
Six lights package
Optional Equipment:
Electrical
+ -Light, warning strobe
Mount, light, warning strobe
Guards
+ -Guard, fuel tank
Guard, fast fuel
Guard, fan debris
Guard, grill debris
Sweeps group
Striker bars, front
Striker bars, front, suspended
Rear screen
Other Attachments
+ -Drains, ecology, power train
Fan speed, low, cold weather
Grab handles, push arm
Counterweight, additional
Black paint, blade
Window shades
PA140VS winch
W12 E PTO winch
Lift Cylinders
+ -Basic
GRADE with 3D
AutoCarry
Bulldozers
+ -8SU/U – basic, guarded or dual tilt guarded
8SU LGP – basic
8 LGP – single tilt guarded or dual tilt guarded
8A
Push Arms
+ -Single tilt, standard or extreme
Dual tilt, standard or extreme
Ripper Shank Teeth
+ -Multi-shank
Single shank
Single shank, deep ripping
Blades
+ -8SU (10.3 m3/13.4 yd3): – With performance cutting edges and end bits – With performance cutting edges and end bits, plus rock guard and wear plate
8SU – basic: – With rock guard and wear plate – With push plate – With landfill wear plate – LGP – LGP landfill
8U – basic: – With rock guard and wear plate – With landfill wear plate
8A