D8T Track-Type Tractor
360° Exterior View
360° Interior View
At a Glance
|
|
|
|
|
|
|
|
Overview
Expand All +
Engine
+ -| Engine Model | Cat C15 ACERT™ |
| Flywheel Power | 354HP |
| Emissions | U.S. EPA Tier 4 Final/EU Stage IV/Korea Tier 4 |
| Net Power - 1,900 rpm - ISO 9249/SAE J1349 | 354HP |
| Engine Power - 1,600 rpm - ISO 14396 | 394HP |
| Displacement | 928in³ |
| Note (3) | All nonroad Tier 4 Final, Stage IV and Korea Tier 4 Final diesel engines are required to use only Ultra Low Sulfur Diesel (ULSD) with 15 ppm (mg/kg) of sulfur or less, or up to B20 biodiesel blended with ULSD. B20 should meet ASTM D7467 specification (bio |
| Note (4) | Diesel Exhaust Fluid (DEF) used in Cat Selective Catalytic Reduction (SCR) systems must meet the requirements outlined in the International Organization for Standardization (ISO) standard 22241. |
| Bore | 5.4in |
| Stroke | 6.75in |
| Engine Power - 1,700 rpm - SAE J1995 | 363HP |
| Engine Power - 1,700 rpm - ISO 14396 | 359HP |
| Engine Power - 1,700 rpm - ISO 14396 (DIN) | 364HP |
| Net Power - 1,900 rpm - ISO 9249/SAE J1349 (DIN) | 317HP |
| Engine Power - Maximum - ISO 14396 | 359HP |
| Engine Power - Maximum - ISO 14396 (DIN) | 364HP |
| Engine Power - Maximum - SAE J1995 | 363HP |
| Net Power - Rated - ISO 9249/SAE J1349 | 312HP |
| Net Power - Rated - ISO 9249/SAE J1349 (DIN) | 317HP |
| Note (1) | Net power advertised is the power available at the flywheel when the engine is equipped with fan, air cleaner, muffler, and alternator. |
| Note (2) | No derating required up to 3566 m (11,700 ft) altitude, beyond 3566 m (11,700 ft) automatic derating occurs. |
Weights
+ -| Operating Weight | 86900lb |
| Operating Weight - Standard | 87600lb |
| Shipping Weight - Standard SU Blade | 66300lb |
| Operating Weight - LGP | 82496lb |
| Shipping Weight - LGP | 68700lb |
| Note (1) | Operating Weight – Standard: Includes hydraulic controls, blade, tilt cylinder, coolant, lubricants, 100% fuel, ROPS, FOPS cab, SU-Blade, Single-Shank Ripper, 610 mm (24 in) MS shoes, and operator. |
| Note (2) | Operating Weight – LGP: Includes hydraulic controls, blade, tilt cylinder, drawbar, coolant, lubricants, 100% fuel, ROPS, FOPS cab, SU-Blade, 965 mm (38 in) MS shoes, and operator. |
| Note (3) | Shipping Weight – Standard: Includes coolant, lubricants, 20% fuel, ROPS, FOPS cab, and 610 mm (24 in) MS shoes. |
| Note (4) | Shipping Weight – LGP: Includes coolant, lubricants, 20% fuel, ROPS, FOPS cab, and 965 mm (38 in) MS shoes. |
Air Conditioning System
+ -| Air Conditioning | The air conditioning system on this machine contains the fluorinated greenhouse gas refrigerant R134a (Global Warming Potential = 1430). The system contains 2.5 kg of refrigerant which has a CO2 equivalent of 3.575 metric tonnes. |
Blades
+ -| 8SU - Capacity - SAE J1265 | 13.4yd³ |
| 8SU - Width - Over End Bits | 13.3ft |
| 8U - Capacity - SAE J1265 | 15.4yd³ |
| 8U - Width - Over End Bits | 14ft |
| 8A - Capacity - SAE J1265 | 6.8yd³ |
| 8A - Width - Over End Bits | 16.5ft |
| 8SU LGP - Capacity - SAE J1265 | 12.9yd³ |
| 8SU LGP - Width - Over End Bits | 14.9ft |
Transmission
+ -| 1 Forward | 2.1mile/h |
| 2 Forward | 3.8mile/h |
| 3 Forward | 6.6mile/h |
| 1 Reverse | 2.8mile/h |
| 2 Reverse | 5mile/h |
| 3 Reverse | 8.8mile/h |
| 1.0 Forward | 2.2mile/h |
| 2.0 Forward | 4.1mile/h |
| 3.0 Forward | 7mile/h |
| 2.0 Reverse | 4mile/h |
| 3.0 Reverse | 7.3mile/h |
| 1 Forward - Drawbar Pull | 148200lb |
| 2 Forward - Drawbar Pull | 82300lb |
| 3 Forward - Drawbar Pull | 46250lb |
| Drawbar Pull - 1 Forward | 148lb |
| Drawbar Pull - 2 Forward | 81lb |
| Drawbar Pull - 3 Forward | 44lb |
Service Refill Capacities
+ -| Fuel Tank | 165gal (US) |
| DEF Tank | 6.3gal (US) |
| Cooling System | 22.7gal (US) |
| Engine Crankcase* | 10gal (US) |
| Power Train | 41gal (US) |
| Roller Frames - Each | 17.2gal (US) |
| Final Drive - Each | 3.3gal (US) |
| Pivot Shaft Compartment | 10.6gal (US) |
| Hydraulic Tank | 19.8gal (US) |
| Note | *With oil filter |
Operating Weights
+ -| Standard | 87600lb |
| LGP | 83200lb |
Hydraulic Controls
+ -| Pump Type | Piston-type, Variable Displacement |
| Pump Output - Steering | 75gal/min |
| Pump Output - Implement | 64gal/min |
| Tilt Cylinder Flow - Rod End Flow | 35gal/min |
| Tilt Cylinder Flow - Head End Flow | 45gal/min |
| Bulldozer Relief Valve Setting | 3480psi |
| Tilt Cylinder Relief Valve Setting | 3480psi |
| Ripper - Lift - Relief Valve Setting | 3480psi |
| Ripper - Pitch - Relief Valve Setting | 3480psi |
| Steering | 5700psi |
| Note (1) | Steering Pump output measured at 2,364 rpm (pump speed) and 30 000 kPa (4,351 psi). |
| Note (2) | Implement Pump output measured at 1,900 rpm and 6895 kPa (1,000 psi). |
| Note (3) | Electro-hydraulic pilot valve assists operations of ripper and dozer controls. A standard hydraulic system includes four valves. |
| Note (4) | Complete system consists of pump, tank, filter, oil cooler, valves, lines, and control levers. |
Weights - Waste Handler
+ -| Operating Weight - Standard | 87400lb |
| Operating Weight - LGP | 92300lb |
| Shipping Weight - Standard | 73400lb |
| Shipping Weight - LGP | 77900lb |
| Note (1) | Operating Weight – Standard: Includes hydraulic controls, blade, tilt cylinder, coolant, lubricants, 100% fuel, ROPS, FOPS cab, Waste SU-Blade, striker box, 610 mm (24 in) MS shoes, and operator. |
| Note (2) | Operating Weight – LGP: Includes hydraulic controls, blade, tilt cylinder, drawbar, coolant, lubricants, 100% fuel, ROPS, FOPS cab, Waste SU-Blade, 965 mm (38 in) MS shoes, striker box, and operator. |
| Note (3) | Shipping Weight – Standard: Includes coolant, lubricants, 20% fuel, ROPS, FOPS cab, striker box, and 610 mm (24 in) MS shoes. |
| Note (4) | Shipping Weight – LGP: Includes coolant, lubricants, 20% fuel, ROPS, FOPS cab, striker box, and 965 mm (38 in) MS shoes. |
Winches
+ -| Winch Model | PA 140OVS |
| Weight* | 3947lb |
| Oil Capacity | 4gal (US) |
| Increased Tractor Length | 22.2in |
| Winch Case - Width | 45.6in |
| Drum Width | 12.6in |
| Flange Diameter | 18in |
| Cable Ferrule Size - Length | 2.76in |
| Cable Ferrule Size - Outside Diameter | 2.36in |
| Drum Capacity - Optional Cable | 193ft |
| Drum Capacity - Recommended Cable Size | 276ft |
| Optimal Cable Size | 1.25in |
| Recommended Cable Size | 1.13in |
| Winch Length | 56.3in |
| Note (1) | *Weight: Includes pump and operator controls. |
| Note (2) | Variable speed, hydraulically driven, dual braking system, three roller fairlead. |
Dimensions - Standard
+ -| Width - Tractor - Without Trunnions - Standard Shoes | 106in |
| Machine Height - ROPS/FOPS Cab | 140.4in |
| Length - Track on Ground | 126.2in |
| Overall Length - Basic Tractor | 183in |
| Ground Pressure (ISO 16754) | 13psi |
| Ground Clearance | 24.1in |
Undercarriage - LGP
+ -| Ground Clearance | 24.1in |
| Ground Contact Area | 9593in² |
| Ground Pressure (ISO 16754) | 7.7psi |
| Grouser Height | 3.1in |
| Length - Track on Ground | 126in |
| Pitch | 8.5in |
| Shoe Type | Moderate Service |
| Shoes/Side | 44 |
| Track Gauge | 92in |
| Track Rollers - Each Side | 8 |
| Width - Shoe | 38in |
Undercarriage - Standard
+ -| Ground Clearance | 24.1in |
| Ground Contact Area | 6060in² |
| Ground Pressure (ISO 16754) | 13psi |
| Grouser Height | 3.1in |
| Length - Track on Ground | 126in |
| Pitch | 8.5in |
| Shoe Type | Moderate Service |
| Shoes/Side | 44 |
| Track Gauge | 82in |
| Track Rollers - Each Side | 8 |
| Width - Shoe | 24in |
Blades - 8A
+ -| Height | 3.9ft |
| Digging Depth | 24.6in |
| Ground Clearance | 52.1in |
| Maximum Tilt | 28.9in |
| Weight* - Without Hydraulic Controls | 11900lb |
| Total Operating Weight** - With Blade and Single-Shank Ripper | 88700lb |
| Note (1) | *Includes blade tilt cylinder. |
| Note (2) | **Operating Weight: Includes hydraulic controls, blade tilt cylinder, coolant, lubricants, 100% fuel, ROPS, FOPS cab, blade, single-shank ripper, 610 mm (24 in) MS shoes, and operator. |
| Capacity - SAE J1265 | 6.8yd³ |
| Width - Over End Bits | 16.6ft |
Blades - 8SU LGP
+ -| Capacity - SAE J1265 | 12.9yd³ |
| Width - Over End Bits | 14.9ft |
| Height | 5.3ft |
| Digging Depth | 20.2in |
| Ground Clearance | 51.5in |
| Maximum Tilt | 35.7in |
| Weight* - Without Hydraulic Controls | 11150lb |
| Total Operating Weight** - With Blade and Single-Shank Ripper | 82496lb |
| Note (1) | *Includes blade tilt cylinder. |
| Note (2) | **Operating Weight: Includes hydraulic controls, blade tilt cylinder, coolant, lubricants, 100% fuel, ROPS, FOPS cab, blade, single-shank ripper, 610 mm (24 in) MS shoes, and operator. |
Blades - 8 SU Landfill
+ -| Capacity - SAE J1265 | 25.6yd³ |
| Width - Over End Bits | 12.9ft |
| Height | 8.1ft |
| Digging Depth | 22.6in |
| Ground Clearance | 50.7in |
| Maximum Tilt | 35.1in |
| Weight* - Without Hydraulic Controls | 7867lb |
| Total Operating Weight** - With Blade and Single-Shank Ripper | 88800lb |
| Note (1) | *Includes blade tilt cylinder. |
| Note (2) | **Operating Weight: Includes hydraulic controls, blade tilt cylinder, coolant, lubricants, 100% fuel, ROPS, FOPS cab, blade, single-shank ripper, 610 mm (24 in) MS shoes, and operator. |
Blades - 8U Landfill
+ -| Capacity - SAE J1265 | 27.7yd³ |
| Width - Over End Bits | 13.9ft |
| Height | 8.3ft |
| Digging Depth | 22.3in |
| Ground Clearance | 48.8in |
| Maximum Tilt | 39.2in |
| Weight* - Without Hydraulic Controls | 9450lb |
| Total Operating Weight** - With Blade and Single-Shank Ripper | 90383lb |
| Note (1) | *Includes blade tilt cylinder. |
| Note (2) | **Operating Weight: Includes hydraulic controls, blade tilt cylinder, coolant, lubricants, 100% fuel, ROPS, FOPS cab, blade, single-shank ripper, 610 mm (24 in) MS shoes, and operator. |
Blades - 8 SU LGP Landfill
+ -| Capacity - SAE J1265 | 28.9yd³ |
| Width - Over End Bits | 14.9ft |
| Height | 7.9ft |
| Digging Depth | 20.2in |
| Ground Clearance | 51.5in |
| Maximum Tilt | 35.7in |
| Weight* - Without Hydraulic Controls | 7734lb |
| Total Operating Weight** - With Blade and Single-Shank Ripper | 83635lb |
| Note (1) | *Includes blade tilt cylinder. |
| Note (2) | **Operating Weight: Includes hydraulic controls, blade tilt cylinder, coolant, lubricants, 100% fuel, ROPS, FOPS cab, blade, single-shank ripper, 610 mm (24 in) MS shoes, and operator. |
Ripper - Multi-Shank, Adjustable Parallelogram
+ -| Total Operating Weight* - With SU-Blade and Ripper | 86876lb |
| Note | *Total Operating Weight: Includes hydraulic controls, blade tilt cylinder, coolant, lubricants, 100% fuel. ROPS, FOPS cab, blade, single-shank ripper, 610 mm (24 in) MS shoes, and operator. |
| Maximum Clearance Raised - Under Tip, Pinned in Bottom Hole | 23.35in |
| Maximum Penetration - Standard Tip | 30.7in |
| Maximum Penetration Force - Shank Vertical | 27920lb |
| Number of Pockets | 3 |
| Overall Beam Width | 97in |
| Pry-Out Force - Multi-Shank Ripper with One Tooth | 51230lb |
| Weight - Each Additional Shank | 732lb |
| Weight - With One Shank | 8681lb |
Standards
+ -| Note (4) | The declared dynamic operator sound pressure level is 75 dB(A) when “ISO 6396:2008” is used to measure the value for an enclosed cab. The measurement was conducted at 70% of the maximum engine cooling fan speed. The sound level may vary at different engin |
| Note (5) | The declared exterior sound power level is 113 dB(A) when the value is measured according to the dynamic test procedures and the conditions that are specified in “ISO 6395:2008.” The measurement was conducted at 70% of the maximum engine cooling fan speed |
| FOPS | Falling Object Protective Structure (FOPS) meets the following criteria: ISO 3449:2005 Level II. |
| ROPS | Rollover Protective Structure (ROPS) meets the following criteria: ISO 3471:2008. |
| Note (1) | The declared dynamic operator sound pressure level is 76 dB(A) when “ISO 6396:2008” is used to measure the value for an enclosed cab. The measurement was conducted at 70% of the maximum engine cooling fan speed. The sound level may vary at different engin |
| Note (2) | Hearing protection may be needed when the machine is operated with an open operator station for extended periods or in a noisy environment. Hearing protection may be needed when the machine is operated with a cab that is not properly maintained or when th |
| Note (3) | Sound Level Information for Machines in European Union Countries and in Countries that Adopt the “European Union Directives” – The information below applies to only the machine configurations that have the “CE” mark on the Product Identification Plate. |
| Brakes | Crawler Machine Brake Requirements meets the following criteria: ISO 10265:2008. |
Blades - 8SU - Version 1
+ -| Capacity - SAE J1265 | 11.3yd³ |
| Digging Depth | 22.6ft |
| Ground Clearance | 50.7in |
| Height | 5.5in |
| Maximum Tilt | 35.1lb |
| Note (1) | *Includes blade tilt cylinder. |
| Note (2) | **Operating Weight: Includes hydraulic controls, blade tilt cylinder, coolant, lubricants, 100% fuel, ROPS, FOPS cab, blade, single-shank ripper, 610 mm (24 in) MS shoes, and operator. |
| Total Operating Weight** - With Blade and Single-Shank Ripper | 86900ft |
| Weight* - Without Hydraulic Controls | 10100lb |
| Width - Over End Bits | 12.9in |
Blades - 8SU - Version 2
+ -| Capacity - SAE J1265 | 13.4yd³ |
| Digging Depth | 22.8in |
| Ground Clearance | 48.7in |
| Height | 5.7ft |
| Maximum Tilt | 36in |
| Note (1) | *Includes blade tilt cylinder. |
| Note (2) | **Operating Weight: Includes hydraulic controls, blade tilt cylinder, coolant, lubricants, 100% fuel, ROPS, FOPS cab, blade, single-shank ripper, 610 mm (24 in) MS shoes, and operator. |
| Total Operating Weight** - With Blade and Single-Shank Ripper | 86900lb |
| Weight* - Without Hydraulic Controls | 10557lb |
| Width - Over End Bits | 13.3ft |
Blades - 8U
+ -| Capacity - SAE J1265 | 15.4yd³ |
| Digging Depth | 22.3in |
| Ground Clearance | 48.8in |
| Height | 5.7ft |
| Maximum Tilt | 39.2in |
| Note (1) | *Includes blade tilt cylinder. |
| Note (2) | **Operating Weight: Includes hydraulic controls, blade tilt cylinder, coolant, lubricants, 100% fuel, ROPS, FOPS cab, blade, single-shank ripper, 610 mm (24 in) MS shoes, and operator. |
| Total Operating Weight** - With Blade and Single-Shank Ripper | 88300lb |
| Weight* - Without Hydraulic Controls | 11500lb |
| Width - Over End Bits | 13.9ft |
Ripper - Single-Shank, Adjustable Parallelogram
+ -| Maximum Clearance Raised - Under Tip, Pinned in Bottom Hole | 25in |
| Maximum Penetration - Standard Tip | 44.4lb |
| Maximum Penetration Force - Shank Vertical | 28620lb |
| Note | *Total Operating Weight: Includes hydraulic controls, blade tilt cylinder, coolant, lubricants, 100% fuel. ROPS, FOPS cab, blade, single-shank ripper, 610 mm (24 in) MS shoes, and operator. |
| Number of Pockets | 1 |
| Pry-Out Force | 50070in |
| Total Operating Weight* - With SU-Blade and Ripper | 86900lb |
| Weight* - Without Hydraulic Controls | 8705lb |
Dimensions - Non-Suspended
+ -| Width - Tractor - Without Trunnions - Standard Shoes | 106in |
| Machine Height - ROPS/FOPS Cab | 140.7in |
| Length - Track on Ground | 128.3in |
| Overall Length - Basic Tractor | 183in |
| Ground Pressure (ISO 16754) | 13psi |
| Ground Clearance | 23.8in |
Dimensions - LGP
+ -| Width - Tractor - Without Trunnions - Standard Shoes | 130in |
| Machine Height - ROPS/FOPS Cab | 140.4in |
| Length - Track on Ground | 126.2in |
| Overall Length - Basic Tractor | 183in |
| Ground Pressure (ISO 16754) | 7.7psi |
| Ground Clearance | 2401in |
Dimensions
+ -| Note (1) | Add the following measurements for attachments: Ripper (single shank) 1519 mm/59.8 in; Ripper (multi-shank) 1613 mm/63.5 in; Drawbar 406 mm/16.0 in; SU Blade 1844 mm/72.6 in; U Blade 2241 mm/88.2 in; A Blade (not angled) 2027 mm/79.8 in; A Blade (angled 2 |
| Note (2) | When Cat Grade Control 3D antennas are installed, overall machine height increases by approximately 82 mm/3.2 in. |
Standard Equipment:
Power Train
-
C15 ACERT Diesel Engine: – Electronic Unit Injection (EUI) – Aftertreatment – Meets Tier 4 Final/Stage IV/Korea Tier 4 emission standards
-
24V electric start
-
High performance single plane cooling system
-
Aftercooler, air-to-air (ATAAC)
-
Air filter, with electronic service indicator
-
Coolant, extended life
-
Fan, suction, hydraulically driven
-
Fuel priming pump, electric
-
Sound attenuated exhaust system
-
Parking brake, electronic
-
Precleaner, strata-tube dust ejector
-
Prescreener
-
Shift management: – Automatic directional and downshift – Controlled-throttle, load-compensated – Enhanced Auto Shift
-
Starting aid, automatic ether
-
Torque divider
-
Transmission, electronically-controlled powershift, 3F/3R speed
-
Four planet, double-reduction planetary final drives
-
Transmission control module, electronic
-
Turbocharger
-
Water separator
Undercarriage
-
Rollers and idlers, lifetime lubricated
-
Sprocket rim segments, replaceable
-
Suspension-type undercarriage
-
8-roller tubular track roller frame (Carrier roller ready)
-
Track adjusters, hydraulic
-
Track guide
-
610 mm (24 in) PPR moderate service grouser with sealed and lubricated track (44 section)
-
Two-piece master links
Hydraulics
-
Hydraulics, independent steering and work tool pumps
-
Hydraulics, electronically controlled, load-sensing dozer lift and tilt
-
Electronically enabled quick drop valve
Starters, Batteries, And Alternators
-
Alternator, 150 amp
-
Batteries, heavy duty
-
Starting receptacle, auxiliary
Electrical
-
Alarm, back-up
-
Converter, 24V to 12V
-
Diagnostic connector
-
Ground level service center with hour meter
-
Horn, forward warning
Operator Environment
-
ROPS mounted air conditioner
-
Armrest, adjustable
-
Advisor operator interface: – Electronic monitoring system – Diagnostic service information – Operator preferences
-
Cab, ROPS/FOPS, sound suppressed
-
Deactivation switch, hydraulic controls
-
Access/egress lighting with shutdown timer
-
Decelerator pedal
-
Governor switch, electronic
-
Heater and ventilation
-
Mirror, rearview
-
Radio-ready
-
Provision for wire passage in/out of cab
-
Interior LED courtesy lights
-
Seat, cloth, air-suspension
-
Seat belt, retractable
-
Steering control, direction and speed control thumb switches with recall button
-
Wipers, intermittent
Other Standard Equipment
-
CD ROM Parts Book
-
Engine enclosures
-
Equalizer bar, pinned
-
Front pull device
-
Guards, bottom hinged
-
Grade control ready
-
HVAC box – corrosive resistant
-
Mounting, lift cylinders
-
Oil cooler, hydraulic
-
Product Link
-
S·O·S sampling ports
-
Steering, electronically controlled power differential
-
Vandalism protection for fluid compartments
-
Engine compartment service light
-
Six lights package
Optional Equipment:
Electrical
Light, warning strobe
Mount, light, warning strobe
Guards
Guard, fuel tank
Guard, fast fuel
Guard, fan debris
Guard, grill debris
Sweeps group
Striker bars, front
Striker bars, front, suspended
Rear screen
Other Attachments
Drains, ecology, power train
Fan speed, low, cold weather
Grab handles, push arm
Counterweight, additional
Black paint, blade
Window shades
PA140VS winch
W12 E PTO winch
Lift Cylinders
Basic
GRADE with 3D
AutoCarry
Bulldozers
8SU/U – basic, guarded or dual tilt guarded
8SU LGP – basic
8 LGP – single tilt guarded or dual tilt guarded
8A
Push Arms
Single tilt, standard or extreme
Dual tilt, standard or extreme
Ripper Shank Teeth
Multi-shank
Single shank
Single shank, deep ripping
Blades
8SU (10.3 m3/13.4 yd3): – With performance cutting edges and end bits – With performance cutting edges and end bits, plus rock guard and wear plate
8SU – basic: – With rock guard and wear plate – With push plate – With landfill wear plate – LGP – LGP landfill
8U – basic: – With rock guard and wear plate – With landfill wear plate
8A
*This estimate is for the base rental charge only. Other fees and charges may apply and will be calculated at the time of rental. Does not include delivery fees.
*Images are for general reference only. Individual product models may vary. Please consult with your dealer to verify machine configuration.
*Images are for general reference only. Individual product models may vary. Please consult with your dealer to verify machine configuration.