Standard Equipment:
Air Inlet System
+ -Air cleaner; light duty with disposable element
Cooling System
+ -Caterpillar extended life coolant
Fan drive, battery charging alternator drive
Coolant drain line with valve
Radiator and cooling fan with guards
Control Panel
+ -EMCP 4 Genset Controller
EMCP 4.1
Exhaust System
+ -Stub pipe, gaskets, raincap and SAE exhaust flange for customer use - shipped loose
Fuel
+ -Secondary fuel filter
Primary fuel filter with integral water separator
Fuel priming pump
Fuel System
+ -Standard open set fuel tank / base supplied base, formed steel with single wall integral 8-hour fuel tank
Generator
+ -Matched to the performance and output characteristics of Cat engines
IP23 Protection
Load adjustment module provides engine relief upon load impact and improves load acceptance and recovery time
Tower panel, IP22, bottom cable entry
Segregated low voltage (AC/DC) wiring panel
Voltage regulator (single phase sensing)
Circuit breaker, IEC, 3 pole, mounted in tower panel
12 leads
IP23 protection
Governing System
+ -Mechanical and electrical governing system - model dependent
Lube System
+ -Oil drain line with valve
Lubricating oil
Mounting System
+ -Captive linear vibration isolators between base and engine-generator
Includes lifting provision and drag points
Termination points for coolant and lube oil drain lines
Mounting
+ -Rubber vibration isolators
Starting/charging System
+ -24V battery with rack and cables
General
+ -Paint - Caterpillar Yellow except rails and radiators gloss black
Engine and alternator pre-paint, Caterpillar yellow
Starting/charging
+ -Batteries
24 volt starting motor
Optional Equipment:
Exhaust
+ -Industrial, Residential, Critical Mufflers
Generator
+ -Oversize and premium generators
Excitation: [ ] Permanent Magnet Excited (PM) [ ] Internally Excited (IE)
Anti-condensation heater
Alternator System
+ -3 phase sensing
Permanent magnet
Quadrature droop kit
LC frame alternator with coastal insulation protection
Anti-condensation heater
R frame auxilliary winding
LC frame alternator
Circuit Breakers
+ -Circuit Breaker Upgrades - 4 Pole circuit reaker to 250A, 400A and 630 A
Power Termination
+ -Circuit breakers, IEC compliant
Circuit breakers, UL listed
Control Panels
+ -Remote monitoring software
Local & remote annunciator modules
EMCP (4.2) (4.3) (4.4)
Digital I/O module
Load share module
Cooling System
+ -Coolant heater
Low coolant level shutdown
Low coolant temp alarm
Control Panel Options
+ -Earth fault (2 wire only)
Panel mounted audible alarm
Control panel heater
Overload shutdown via breaker
Earth leakage (2 wire only)
Emergency stop with key
Battery charger
Volt free contacts
Voltage adjust potentiometer
Speed adjust potentiometer
EMCP 4.2
Starting/charging
+ -Charging alternator
Oversize batteries
Jacket water heater
Battery chargers
Heavy-duty starting system
Enclosures
+ -Sound attenuated Level 2 enclosure
Rental pack - CAE rental option only
Sound attenuated Level 1 (galv)
European Certifications
+ -Upgrade to STD set for CE
Fuel System
+ -Low fuel level shutdown
Low fuel level alarm
Compact skidbase for open set
Bunded fuel tank
Skidbase for CALG enclosure sets
Open set narrow base
High fuel level alarm
General
+ -CSA Certification
Sound attenuated, weather protective or high ambient weather protective enclosure
Single or dual wall sub-base fuel tanks
Single or dual wall integral fuel tanks
Narrow, Wide or Skid Base
EEC Declaration of Conformity
EU Certificate of Conformance (CE)
Automatic transfer switches (ATS)
Integral & sub-base fuel tanks
Seismic Certification per applicable building codes: IBC 2000, IBC 2003, IBC 2006, IBC 2009, CBC 2007
UL 2200 package
Global Certifications
+ -Mounting Options
+ -Industrial silencer
Battery removal
Electronic governor
External single point lift - enclosure
Silencer installation kit
Special Packing/inspectons For Shipment
+ -PGS test report @ 0.8 power factor
PGS test report @ 1.0 power factor
General - Accessories / Miscellaneous
+ -Packing case - compact set
Stone guards / rad trans flange
Packing case - canopied set